| |
Eas y Prints® Numbers |
For Hotronix®
Temperature/Time: 340° for 8 seconds
(other
machines at 350° or higher)
or
Temperature/Time: 365° for 4 seconds
(other
machines at 375° or higher)
Pressure: Med/Firm 6-8
Allow for warm up time. |
 |
Preheat
Bottom Pad
Before applying, lock the top platen down for 60 seconds.
This helps the ink to flow properly during the application. |
| NOTE: These recommended time, temperature and pressure settings are for Stahls' Hotronix® heat seal machines. Settings on other heat presses may vary based on their inconsistencies.
|
| For Application on cotton, polyester or poly/cotton
blends. Downloadable
PDF |
|
| 1. Preheat Garment |
| Place garment on platen and press for 3-5 seconds
or until there is no more steam to remove wrinkles
and moisture. |
 |
| Check to be sure there are no obstructions such as buttons, pockets or seams. If there are, raise print area only with Print Perfect pad or mouse pad. |
|
| 3. Press |
 Close machine and press.
340° for 8 seconds
or
365° for 4 seconds |
|
| 2. Position |
Position on garment
ink side down. |
 |
|
| 4. Peel |
Open
machine,
pause 5 seconds and peel. |
 |
|
|
|
| |
Easy Prints® Letters |
For Hotronix®
Temperature/Time: 340° for 8 seconds
(other
machines at 350° or higher)
or
Temperature/Time: 365° for 4 seconds
(other
machines at 375° or higher)
Pressure: Med/Firm 6-8
Allow for warm up time. |
|
Preheat Bottom
Pad
Before applying, lock the top platen down for 60
seconds. This helps the ink to flow properly during
the application. |
| NOTE: These recommended time, temperature and pressure settings are for Stahls' Hotronix® heat seal machines. Settings on other heat presses may vary based on their inconsistencies.
|
| For Application on cotton, polyester or poly/cotton blends. Downloadable
PDF |
|
| 1. PEEL |
| Peel desired letters off of release paper, by peeling from one corner. |
 |
|
| 3. PRESS |
Close machine and press.
340° for 8 seconds
or
365° for 4 seconds |
|
|
| 2. POSITION |
| Position on garment. Cover with cover sheet provided. |
 |
|
| 4. REMOVE COVER SHEET |
Open machine.
Peel off cover sheet. |
 |
|
|
|
| |
Express Names™ |
For Hotronix®
Temperature/Time: 340° for 8 seconds
(other
machines at 350° or higher)
or
Temperature/Time: 365° for 4 seconds
(other
machines at 375° or higher)
Pressure: Med/Firm 6-8
Allow for warm up time. |
|
Preheat Bottom
Pad
Before applying, lock the top platen down for 60
seconds. This helps the ink to flow properly during
the application. |
| NOTE: These recommended time, temperature and pressure settings are for Stahls' Hotronix® heat seal machines. Settings on other heat presses may vary based on their inconsistencies.
|
| For Application on cotton, polyester or poly/cotton blends. Downloadable
PDF |
|
| 1. Preheat Garment |
 Place garment on platen and press for 3-5 seconds or until there is no more steam to remove wrinkles and moisture. Check to be sure there are no obstructions such as buttons, pockets or seams. If there are, raise print area only with Print Perfect pad or mouse pad. |
|
| 3. Press |
Close machine and press.
340° for 8 seconds
or
365° for 4 seconds |
|
| 2. Position |
Position on garment ink side down.
Numbers and Express Names™ can be applied at the same time. |
 |
|
| 4. Peel |
Open machine, and peel off release paper.
Note: If applying with Numbers, remove paper from Express Names™ - FIRST. |
 |
|
|
|
| |
Glitter |
| |
Temperature: 350° for
Hotronix®
(other machines
at 360° or higher)
Time: 15
Seconds
Pressure: Med/Firm 6-8
Allow for warm up time. |
|
Preheat
Bottom Pad
Before applying, lock the
top platen down for 60 seconds. This helps
the ink to flow properly during the application. |
| NOTE: These recommended time, temperature and pressure settings are for Stahls' Hotronix® heat seal machines. Settings on other heat presses may vary based on their inconsistencies. |
| For Application on cotton, polyester or poly/cotton blends. Downloadable PDF |
|
| |
| 1. Preproduction |
| Please check transfers carefully before applying. We provide an extra transfer for testing to your quality standards. Cut transfer into 4 pieces and apply on test material until desired results are achieved. If you are unable to get desired results, please call us before starting job. |
|
| 3. Press |
 Place
the transfer face down on the garment.
Close machine and press 15 seconds. |
|
| 2. Preheat Garment |
 Place
garment on platen and press for 3-5 seconds or
until there is no more steam to remove wrinkles
and moisture. Check to be sure there are no obstructions
such as buttons, pockets or seams. If there are,
raise print area only with Print Perfect pad or
mouse pad. |
|
| 4. Peel COLD |
 Open machine, allow print to cool completely to the touch.
Peel off transfer paper in a smooth, even motion. |
|
|
|
| |
|
| |
| Need a new press? See our
selection of heat presses you can purchase online. |
|
Goof Proof®